Home > Silicone Hoses >

Torque Solution 3" (76mm) Turbo Inlet Hose (Non-Recirc): Subaru WRX 02-07, STI 04-20, LGT 05-2009, FXT 04-13
3" Turbo Inlet Hose


 
Alternative Views:


MSRP$269.99
Sale Price:$242.99
You save $27.00!

Product Code: TS-SU-565-NR
Qty:

Description
 
Torque Solution 3" (76mm) Turbo Inlet Hose (Non-Recirculated)
Applications: Subaru WRX 2002-2007, STI 2004-2020, Legacy GT 2005-2009, Forester XT 2004-2013

Torque Solution Turbo Inlet Hose for the Subaru EJ Engines w/ 3" Inlet Turbo.. Our silicone inlet hose is much larger in size and smooths the air entering the turbo compared to the restrictive OEM corrugated inlet hose. Our inlet hose is made from 4 ply high grade silicone and wire reinforced to prevent collapsing under high pressure. We include 2 black anodized billet aluminum joiners to connect to either 2.75" or 3" intakes.

- Smooths Airflow Entering Turbo
- Increases Air Flow
- Eliminates failure prone corrugated rubber hose
- 4 Ply Silicone w/ Wire Reinforcement
- Includes Silicone Friendly Stainless Steel Hose Clamps
- Direct Fitment for Aftermarket 3" (76mm) Inlet Turbo's
- Non Recirculated for Vent to Atmosphere (Speed Density) Set Ups
- Limited Lifetime Warranty

Includes:
- 3" Non Recirc Black Silicone Turbo Inlet Hose (1)
- 3" Billet Aluminum Coupler (for 3" Intakes) (1)
- 3" to 2.75" Billet Aluminum Reducer Coupler (for 2.75" Intakes) (1)
- 70-90mm Silicone Safe Worm Gear Clamp (2)
- 3/8" 90 Degree Nylon Elbows (3)
- 1/2" to 3/8" 90 Degree Nylon Reducer Elbows (2)
- 1/2" to 3/8" Straight Nylon Reducer (2)
- 5/16" to 3/8" Straight Nylon Reducer (2)
- 1/2" Nylon T Fitting (1)
- 1/2" Fuel/PCV Hose (13")
- 1/8 NPT Stainless Plugs (4) (for DIY TGV Delete)
- Heavy Duty 10 Inch Zip Ties (5)

**We recommend either using our billet TGV deletes or using the supplied 1/8 NPT plugs to delete the factory TGV for clearance.

***Important note: The Torque Solution inlet bypasses the PCV Diagnosis Port. You will need to perform a simple bypass.

1. Locate PCV Diagnosis connector (grey or white depending on year), which located on the block next to throttle body.
2. You will need to use a pair of needle nose pliers to remove the jumper pin inside the PCV Diagnosis connector. This pin should pull out easily only using slight pressure. Do not discard the jumper pin removed from the connector.
3. Place the jumper pin into the female harness plug that was connected to PCV diagnosis connector. Use electrical tape to secure in place.



PROPOSITION 65

Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm.

WARNING: Cancer and Reproductive Harm. (http://www.p65warnings.ca.gov)


Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Silicone Hoses
Silicone Hoses > Turbo Inlet Hose
Select Your Car
Select Your Car > SUBARU
Select Your Car > SUBARU > Impreza WRX STi 2008-2014
Select Your Car > SUBARU > Legacy GT 2005-2009
Select Your Car > SUBARU > Forester XT 2004-2008
Select Your Car > SUBARU > Impreza WRX 2008-2014
Select Your Car > SUBARU > Impreza WRX 2006-2007
Select Your Car > SUBARU > Impreza WRX 2002-2007
Select Your Car > SUBARU > Impreza WRX STi 2006-07
Select Your Car > SUBARU > Forester Xt 06-11
Select Your Car > SUBARU > Impreza WRX STI 2015+