Home > Inserts > Engine Mount Inserts >

Torque Solution Lower Engine Mount Inserts: Hyundai Veloster 2011+
Torque Solution Lower Engine Mount Inserts: Hyundai Veloster 2011+
 
MSRP$49.99
Our Price:$44.99
You save $5.00!


Product Code: TS-HV-002
Qty:

Description
 
Torque Solution Lower Engine Mount Inserts
Applications: Hyundai Veloster 2011+

Torque Solution polyurethane engine mount inserts that replace the soft inner rubber material of the OEM Lower Engine Mount. Includes 2pcs for each application. These give you improved traction and reduced wheel hop without too much vibration. Also stops the pitching of the engine under hard acceleration and on/off throttle situations which in return allows you to put the power to the ground!!!!

Eliminates wheel hop / traction loss

- Improved 60fts / e.t's
- Street and track torture tested
- 75A durometer bushings
- Limited Lifetime Warranty



PROPOSITION 65

Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that cause cancer, birth defects or other reproductive harm.

WARNING: Cancer and Reproductive Harm. (http://www.p65warnings.ca.gov)


Average Customer Review: Average Customer Review: 4.5 of 5 4.5 of 5 Total Reviews: 2 Write a review.

  0 of 0 people found the following review helpful:
 
5 of 5 Perfect fit March 25, 2021
Reviewer: Marc-Antoine from Montreal, QC  
With exchange and shipping, the price is a bit steep, but they do what is advertised for a 2014 Veloster. With a little persuasion, they install rather easily and they do what they are meant - they kill engine rocking under load. Vibration and noise transfer is, in my opinion, rather noticeable but I was actually looking for a bit more transfer from the engine. It is completely acceptable, and unless your passengers expect a limousine ride, it shouldn't bother many people.

Was this review helpful to you?

  0 of 0 people found the following review helpful:
 
4 of 5 Work on Elantra Sport - sorta March 25, 2019
Reviewer: Nate  
I went ahead and got these inserts for my Elantra Sport. The bushings from the car are almost the same size except these were a bit taller and so stiff that I could only install one of them. I coudn't put the bolt back through the mount with both polyurethane inserts. However, I read some reviews on forums and watched some videos and came to the conclusion that only installing 1 helps minimize vibration further and still has plenty of added benefit. I installed the Torque Solution insert on the side of the mount that slides into the sub-frame to help most with pitching of the engine under acceleration. I left the factory bushing on the adjacent side but definitely squished it a bit more when I put the bolt in. I subtracted a star because they do not look as pictured. There are no notches at the bottom which I would think would provide some vibration relief. I'm very happy with my purchase.

Was this review helpful to you?


Browse for more products in the same category as this item:

Inserts > Engine Mount Inserts
Inserts
Select Your Car > HYUNDAI > Veloster 1.6L 2011+
Select Your Car
Select Your Car > HYUNDAI


Torque Solution Map Sensor Adapter PNP Harness: Ford Focus ST / Fiesta ST $19.99
Torque Solution Billet Shift Knob (Purple): Universal 10x1.5 $31.49
Torque Solution Multi-Layer Stainless Gasket: Subaru EJ Uppipe To Turbo $13.99
Torque Solution Reverse-Flow Silicone Radiator Hose Kit: Honda Civic Type-R FK8 / Accord 2.0T 18-22 $134.99
Torque Solution Brake Master Cylinder Brace: Toyota GR Supra MK5 2020+ $129.99
Torque Solution Fiberglass Exhaust Wrap (Tan): Universal 2" x 50' $17.99
Torque Solution Replacement Part: Rectangle Mount Urethane for Various VW Mounts $35.99
Torque Solution Rear Toe Link Kit: Porsche 981 / 718 Cayman & Boxster $589.99
Torque Solution Thermal Intake Manifold Gasket: Honda Del Sol Si 1996 1997 D16Y8 $39.99